Capacitors

  • Mojotone Pre-Wired Strat HSS Wiring Harness

    Mojotone Pre-Wired Strat HSS Wiring Harness The Mojotone Pre-Wired Strat HSS Wiring Harness It’s all about the tone! There’s no words to describe the highest level of quality we provide with our wiring kits and components. Bring your guitar to life with our smooth custom taper CTS potentiometers and creamy sounding oil filled Vitamin T capacitors for a vast improvement over your stock electronics! This is a 5-way super switch kit for HSS style Strats with a humbucker in the bridge position. It uses a master volume, shared tone control for the neck and middle pickups, and a tone control for the bridge pickup. 500k pots give the humbucker the correct load and we use a resistor on the single coils to give them the correct 250k load so there is no compromise mixing single coils with humbuckers. Use 24 knurl push on knobs for the split shaft pots. Features and Benefits Vintage quality USA branded components (Switchcraft, Mojotone, CRL, and CTS)! USA made CRL Switch! It’s the most reliable and smoothest feeling switch ever made and hasn’t changed since the 50’s. Smooth custom taper, CTS industrial potentiometers with solid brass bushings and the tightest tolerances available. Handcrafted and hermetically sealed Mojotone Vitamin T oil-filled tone caps! Hand-wired point-to-point by Mojotone in the USA! Standard Control Functions:Master Volume: Top KnobNeck Pickup Tone: Middle KnobMiddle & Bridge Pickup Tone: Bottom Knob5-Way Switch Position 1: BridgePosition 2: Bridge and Middle (humbucker coil tapped)Position 3: MiddlePosition 4: Middle and NeckPosition 5: NeckIncluded: -Mojotone custom CTS 500k split shaft potentiometers -Oak Grigsby 5-way super switch -Switchcraft mono input jack -Mojotone Vitamin T Oil Filled .047uf capacitor (for single coils) -Mojotone Vitamin T Oil Filled .022uf capacitor (for humbucker) -Pre-tinned cloth covered wire Note:Guitars made overseas may require you to enlarge the holes for the larger US spec pots to fit. You will also need to change the metric knobs to inch sized 24-knurl push-on knobs and the switch tip. See related items.

  • ObsidianWire Tradition Vintage for Jazz Bass pre-wired kit – 250k CTS pots

    ObsidianWire Tradition Vintage for Jazz Bass pre-wired kit – 250k CTS pots The ObsidianWire Traditional Vintage Plus for Strat pre-wired solderless kit – 250k CTS pots & 0.047uf cap ObsidianWire Traditional Vintage Pro-Wired Electronics for Jazz Bass are a pop in replacement for your old J bass wiring harness. The upgrade plays homage to the original design that Leo first started crafting back in 59. We take the design a few steps further with some minor adjustments to improve play-ability, and of course your sound. Best of all, these are super easy to install, and allow for unlimited solder-less pickup changes with ObsidianWire Plug, Play and Enjoy connectors. The Heritage of Traditional Vintage Pro-Wired Electronics for Jazz Bass: ObsidianWire Traditional Vintage Pro-Wired Electronics follow the same tried and true formula of the original Jazz Bass with the addition of premium selected and hand matched components for greater clarity and control over your tone. To make your tone crystal clear at lower volumes we also include an ObsidianWire Custom Spec Treble Bleed Mod. This prevents tone ‘muddiness’ at low volumes by allowing high frequencies to pass along a separate path to your amp, rather than being stopped short by the increasing resistance at the volume control. We build ObsidianWire Pro-Wired Electronics using the world’s best craftsmanship and components: 3 x ObsidianWire Custom Select Pots (Crafted by CTS) 250k or 500k (+/-6%) (Matched to +/-2%) SOLID SHAFT 1 x Genuine Switchcraft J11 Mono Output jack 1 x ObsidianWire Custom Select Capacitor (NOS K42Y-2 0.047uf) or (150 Series Polyester Film 0.022uf) (Hand Tested to +/-10%) 1 x ObsidianWire Premium Selected Volume Mod / Treble Bleed – Improved Volume Taper & Clarity 1 x Pre Printed & Easy to Follow Wiring Diagram Compatibility: ObsidianWire Pro-Wired Electronics for Jazz Bass, are designed to be a direct fit for American and Mexican series Fender® basses. They can also be used to upgrade Japanese Fender & Squier guitars with some adjustments. In the least, you will need a new genuine Fender USA control plate and new 1/4″ knobs to fit the higher grade electronics. We cannot guarantee that these will fit any other guitar. Note: aftermarket control plates do not have the correct Fender spec spacing and as such will not fit our electronics. We recommend a genuine Fender plate – Part Number: 099-2058-000 At ObsidianWire we use US spec 1/4″ Solid shaft controls. We recommend that you check your knobs are the correct size and replace them if necessary.

  • Fender Telecaster Solderless SS Wiring Upgrade with K42-Y2 PIO Tone Capacitor!

    Premium Telecaster wiring harness- No soldering required -Completely wired (Not a kit) – Made for a true drop-in fitFrom Charlies Gear USA Features:Solderless installationFor models with 2 single coil pickups (S-S)NOS, Paper in oil premium quality tone capacitorMulti-contact jack with 100% more signal transfer area2 hardware grounding options includedDedicated control cavity ground helps protect signal against interference Installation:This system is designed to make upgrading your electronics with premium components easy, quick and frustration free. The easiest installation & future pickup swap system available.1- Slip your stripped wires into the terminal ports and secure with the included screwdriver. 2- mount your new harness in the control cavity3- plug the solderless terminal into the harness. BING – BANG – BOOM – DONE! Plus, no burned fingers!***Makes future pickup upgrades a snap***Specifications:CTS 450G 250k audio pots Brass mounting bushings (smooth operation & longer life)Brass solid shaft 1/4″ (for knobs)NOS, K42-Y2 .047uF PIO tone capacitor Oak Grigsby 3 way blade switch (Fender)Pure tone multi-contact mono jackGavitt 22 gauge cloth covered wiring2 hardware grounding options includedDedicated control cavity ground with screw lug end including screwPremium quality solderless terminal for your wiresInstallation wiring guideFast shipping with USPS Ground Advantage delivery Need something different? Just ask! Almost 300 models in the store- OR -Have yours custom made & ready in a few days Check out Charlies Gear for wiring harnesses galore!… www.ebay.com/str/lightninmagic Sales outside USA may require additional import duties

  • ObsidianWire Vintage MKII Les Paul selectable 50’s / 60’s pre-wired kit

    ObsidianWire Vintage MKII Les Paul selectable 50’s / 60’s pre-wired kit The ObsidianWire Vintage MKII Les Paul selectable 50’s / 60’s pre-wired kit The new ObsidianWire MKII Wiring Harness for Les Paul®, allows you to auto switch between 50s & 60s wiring layouts, without having to take anything apart or do any soldering. Just flick the dedicated switch to select your preffered option.Each pickup gets its own switch, so you can even run 50’s wiring on the neck and 60’s wiring on the bridge & vica versa. Vintage 50s Wiring Rich Warm Clean Tones & growling crunch. The 50’s LP® wiring mod is a super popular upgrade that reverts your LP® wiring harness to the glory days of the Vintage Les Paul®.It allows for the perfect amount of treble roll off when you wind back the volume control, for smoothly moving between warm clean tones and growling crunch. Modern 60s Wiring Clarity at All Volumes & Sering LeadsThe ObsidianWire Modern 60s wiring is an improved formula compared to standard modern LP® wiring, designed to prevent treble loss when you roll back the volume. The result is greater clarity and cut through at all volume levels. ObsidianWire Pro-Wired Electronics are built using the world’s best craftsmanship and components: 4 x Premium Selected CTS Split Shaft Pots 500k (+/-6%) (Matched to +/-2%) (Long Shaft with extra nuts can be used with long shaft or short shaft guitars) 1 x Genuine Switchcraft Short Toggle Switch (Pro-Wired for use in Gibson® Les Pauls® + Epiphone® Les Pauls® with a little modification) 2 x Obsidian Select Capacitors (150 Series Polyester Film 0.022uf) (Hand Tested to +/-10%) 1 x Genuine Switchcraft J11 Mono Output jack 1 x Pre Printed & Easy to Follow Wiring Diagram 1 x Endless Customer Support ObsidianWire Pro-Wired Electronics for Les Paul, are designed to be a direct fit for American Gibson® Les Pauls®. They can also be used and are a great upgrade for Epiphone® Les Pauls. Please note that for Epiphones you will need to widen the holes in the body for the higher grade, US spec electronics and get new 24 spline knobs to fit. Attempting to use your old metric knobs will damage your new Pro-Wired Electronics.