P Bass Wiring Harness 250k Bourns Pots w/Treble Bleed Circuit Fender

Get it Fast!…All harnesses are hand crafted and expertly soldered, and usually ship in one day. (Excluding Weekends and Holidays) This pre-wired Harness will greatly improve the tone of your P Bass. Fits any Fender P-Bass or P- Bass Copy withsingle pickup or two pickup’s wired in series.What is Treble Bleed?When you turn down the volume on your Bass you are also turning the tone down resulting in “muddy tone”. A resistor capacitor network “treble bleed” is added to the input and output of the volume control to keep the highs from leaving your tone as the volume is decreased. Adding this circuit helps to avoid the “muddy-tone” syndrome. Install your pre-wired pickups and you’re good to go! Includes: 250K Ohm Bourns Potentiometers. Short-Solid Shaft – Audio Taper, Aluminum bushing and shaft, Long Life Carbon Element. Designed for use in all guitars. Orangedrop .047uf / Tone Capacitor for a smooth warm 50’s Tone Switchcraft 2 Conductor, Mono 1/4″ Output Jack Black and white Vintage style 22awg cloth push back wire. Standard Potentiometer SpecificationsBody Depth0.45 in.Body Diameter0.95 in.Bushing Length0.38 in.Power Rating0.25 WShaft Diameter0.25 in.Shaft Length0.38 in.Value = 250K Ohms

Solderless HH Stratocaster Wiring Harness – 1V / 2T / 3 way

Complete 1 volume, 2 tone, 3 way switch wiring harness for Fender H-H Stratocaster No soldering required !Completely wired (not a kit) Made to fit and ready to drop-in to your axe! Made in USA.Special features:Solderless installationDesigned for Stratocaster with 2 humbucker pickupsChoice of tone capacitorMulti contact jack with 100% more signal transfer area Installation:This system is designed to make upgrading your electronics with premium components easy, quick and frustration free.1- Simply slip your stripped wires into the solderless terminal ports and secure with the included 2mm screwdriver. 2- mount your new harness in the control cavity3- plug the solderless terminal into the harness. BING – BANG – BOOM – DONE! Plus, no burned fingers!***Makes future pickup upgrades a snap***Please NOTE:This is a standard Stratocaster control layout Specifications: Solderless HH Stratocaster wiring harness 1V / 2T / 3 way switchCTS 450G 500k audio potentiometers – 24mm body (full size)Master volume Front tone controls neckRear tone controls bridge Short fine spline split shaft (for knobs)Brass bushings (smooth operation & longer life)Mounting bushing: 3/8″ long x 3/8″ Diameter (threaded section).022uF tone capacitor (choose type from menu above)Oak Grigsby 3 way blade switch – Smooth roller bearing action Pure tone mono jack Gavitt 22 gauge wiringInstallation hardware Premium quality solderless terminal for your pickup wiring and bridge ground2mm screwdriver for terminalInstallation wiring diagramFast shipping with First Class or Expedited Delivery! Can’t find you’re harness? – Just ask – Made to order harness ready in 2 days!Check out Charlies Gear for cool gear & wiring harnesses galorewww.ebay.com/str/lightninmagic Note: Sales outside USA may require additional import duty

Premium Wiring Harness for Stratocaster CTS 275k (9% Tol) Custom Pots

New Premium Wiring Harness for Stratocaster CTS, Mallory Mustard Tone .033uf cap, Oak Grigsby 5 Way Switch. This is a pre-wired Stratocaster wiring harness upgrade for American or Mexican Fender Stratocasters.These are the highest quality Potentiometers that the CTS Corporation manufacture. WD® Music Products developed these high-quality split-shaft potentiometers with CTS® to offer you exceptional performance in electronics for your instrument. These are NOT the same CTS pots that other companies stock and sell. These are developed using 9% +/- tolerances and a value at 10% over the standard 250K rating (275K). This ensures you not only optimum performance but guarantees your potentiometers will always be at least the value stated unlike many others using 20% tolerances where you can be over spec but in most cases way under the specifications you need to ensure good tone from your pickups. They added brass components and a high quality wiper versus what comes standard on most run of the mill pots to ensure long life, quality and consistent performance. Pot Specs and Dimensions: Value 275kTolerance = +/- 9% Bushing Threads = 3/8-32 Bushing Height = 3/8 in. Shaft Type – split Spline Count = 24 Shaft Length – 3/8 in. Hole size requirement = 3/8 in. 2 nuts and 2 washers per pot. This is the famous Mallory® Mustard Cap used on just so many high-end guitars. Upgrade the sound and tone of your Guitar with the high-quality Mallory Mustard Tone 150 series capacitors. Experience cleaner, bell like tones that do not go dark and muddy when rolled down like Orange Drops do. Their great tone makes them a premium upgrade for tone improvement. They also tend to “round off” harsh overdrive sounds. These are the tone capacitors that I use in my own guitars. Original Oak Grigsby 5-way USA Switch.3 x CTS 275K Pots with Brass split shafts and Brass bushings.Mallory Mustard Tone .033uF Capacitor (We also offer a Mallory .022uf capacitor) Let me know at checkout if you need the .022 cap).Gavitt Vintage Style Cloth covered push-back Wire.Switchcraft Jack.We also add 2 ground wires from the volume pot. One for your Tremolo Claw and one for your pickup grounds. Atlantic Custom Guitars hand wired Strat harness featuring all top shelf components. It’s pre-wired and ready to drop into your guitar to upgrade your tone. The front tone is wired for the neck pickup. For the bottom tone we wired a jumper into the circuit, to control both the middle and bridge pickups. (A stock Stratocaster does not have tone for the bridge). Bench tested and guaranteed 100% working. After building it, we hook it up to a Strat in our shop and do a complete test.

Gibson Thunderbird Bass Harness! CTS, Switchcraft, Gavitt Wire, & Orange Drop!

STARR GUITAR replacement electronics for Gibson Thunderbird 3 control Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each SGS “Standard” Thunderbird Bass Harness: 2) CTS 500K Audio Pots (Volume Controls), split shaft, with Nut, Lock, and Dress Washer 1) CTS 250K Audio Pot (Master Tone), split shaft, with Nut, Lock, and Dress Washer 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) Gavitt vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) 18 gauge solid tinned copper master ground wire 1) Switchcraft #11L input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section)1) Assembly template board IMPORTANT: if your bass needs the long switchcraft #151 cannon style jack, I have them here at this link:www.ebay.com/itm/Switchcraft-151-Mono-Long-Threaded-Jack-with-GAVITT-Wire-NEW/283455306152 Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. If so, you will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 www.facebook(dot)com/starrguitarsystems WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.www.wildestarr.comwww.facebook.com/DaveStarr7777www.facebook.com/starrguitarsystemswww.ernieball.com/artists/dave-starrwww.emgpickups.com/artist/index/view/id/407

4PCS Dome Knob Volume Tone Control Knobs with Inner Hexagon Spanner Guitar Bass

Features:If your knobs are dirty, dingy and old, or just want to dress up your guitar, these will work great.Brand new knobs in excellent conditionWith a small wrench , Convenient to useSuitable for LP, TL, A potentiometer guitar can all useType:guitar bass dome tone knobsSize:1.5cm x 1.5cm x 6cmWeight:90gColor:gold/black/silverMaterial:metalQTY:4pcs Package includes: 4pcs guitar bass dome tone knobs with 1pc wrench On Oct-21-21 at 00:50:29 PDT, seller added the following information:

Wiring Harness for P Bass 250k CTS Pots, Orange Drop, Switchcraft

This pre-wired Harness fits Fender P Bass All harnesses are hand crafted and expertly soldered. Orders are usually shipped the next day (excluding weekends and holidays) This pre-wired upgrade kit will greatly improve the tone of your P Bass. Fits any Fender P-Bass or P- Bass Copy withsingle pickup or two pickup’s wired in series.Install your pre-wired pickups and you’re good to go! Includes: 250K Ohm Vintage-Style Potentiometers. Short-Solid Shaft – Audio Taper, Aluminum bushing and shaft, Long Life Carbon Element. Designed for use in all guitars. Orange Drop .047uf / Tone Capacitor for a smooth warm 50’s Tone Switchcraft 2 Conductor, Mono 1/4″ Output Jack Black and White Vintage style 22awg cloth push back wire. Standard Potentiometer SpecificationsBody Depth0.45 in.Body Diameter0.95 in.Bushing Length0.38 in.Power Rating0.25 WShaft Diameter0.25 in.Shaft Length0.38 in.Value = 250K Ohms