Gibson Explorer Bass Wiring Harness Upgade! CTS – Orange Drop – Switchcraft NEW!

Gibson Explorer Bass wiring harness upgrade – NEW! Made to fit the 1980’s circa Gibson Explorer bass (see pics) with 2″ center to center spread between the 3 pots.FREE SHIPPING! EXPBASS system includes: 2) CTS 500K volume pots, audio taper, split shaft, 3/8″ tall threaded collar, requires 3/8″ diameter hole1) CTS 250K master tone pot, audio taper, split shaft, 3/8″ tall threaded collar, requires 3/8″ diameter hole1) Orange Drop .047 Capacitor1) 18 gauge buss master ground wire4) 22 gauge Gavitt vintage cloth wires, white & black1) Switchcraft Jack model #11 or model #151 (see pics) 1) Mounting template1) Wiring info

Prewired Switchcraft 12B 1/4″ stereo output jack with 18 volt mod (EMG) NEW!

Prewired Switchcraft 12B 1/4″ output jack with 18 volt connectors (EMG) NEW! I make these right here in my Houston Texas shop! See photo section for wiring info. Prewired Switchcraft 12B 1/4″ output jack with 18-volt battery (9 volt x 2) connectors and heat shrink tubing. For use with EMG and other brands of active pickups and electronics. FREE SHIPPING! Included:1) Switchcraft 12B Stereo Jack pre-wired with heat shrink protection on all 3 terminals. Includes nut and washer. 1) Gavitt pre tinned 8 inch hot wire WHITE1) Gavitt pre tinned 8 inch hot wire BLACK2) Heavy Duty pre wired 9 volt battery connectors1) Extra heat shrink tubing wiring info: if you are using the older EMG pickups, you will solder the red wire from the battery connector to the red wire coming from the pickups. Cover solder joint with the heat shrink provided. If you are using the modern EMG pickups, you will cut your red battery buss wire on one end and solder that to the red wire coming from the battery connector. Cover solder joint wth the heat shrink provided. (see photo section) 9 volt vs 18 volt info: Headroom (+9 or +18 Volts): Headroom is defined as the ability of the pickup to deliver a clean, undistorted waveform. But…while current is being drained from the battery, the battery voltage is decreasing, and so is the headroom. EMG Pickups never put out more voltage than is being supplied. Using a 9 Volt battery will limit the output signal of the pickup to slightly less than 9 Volts. Older EMG Pickups may have a maximum output of 4.5 Volts, one half of the supply. If you supply the pickups with 18 Volts the headroom will double, creating even more headroom for the signal. Doubling the supply voltage to 18 Volts will increase the amount of current drain. You don’t get something for nothing. (courteous of EMG pickups) Looking for the standard 9 volt version? Follow this link:www.ebay.com/itm/Prewired-Switchcraft-12B-1-4-output-jack-with-9-volt-connector-EMG-NEW/282160761721 Check my ebay store for my custom made Harness upgrades for guitar & bass! Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Fender Telecaster Harness Upgrade! CTS, CRL, Switchcraft, & Orange Drop .047!

STARR GUITAR SYSTEMS replacement electronics for Fender Telecaster! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import telecaster electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each SGS Fender Telecaster “Standard” set: 2) USA made CTS 250K Vintage Style Audio Pots, solid shaft, with Nut, Lock and Dress Washer. 1) USA made CRL 3 way pickup selector switch 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) Vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) Switchcraft #11 input jack with shrink wrap strain relief on both terminals 1) Wiring diagram (see photo section)1) Assembly template board Note: Check out my ebay store Telecaster section to see my “PRO” Tele harness! Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Fender LEFT HAND Tele 4-Way Switch Harness CTS, Tritan, Switchcraft, Orange Drop

Fender Telecaster LEFT HANDED 4-Way Switch Harness! CTS LH POTS, TRITAN, Switchcraft, & Orange Drop! This gives you the usual Tele sounds in the first three positions. But in position 4, you get both pickups in series like a humbucker. It’s a big boost in output and a big, fat tone. But you need to make one important adjustment: The neck pickup’s cover has to be grounded with a separate wire. That means you have to flip the pickup over and cut the little un-insulated jumper wire that connects to the cover. That leaves a 1/4-inch nub of wire connected to the cover. Attach a new wire to that, and connect it to ground. This wiring works great with any vintage-output Tele pickups. STARR GUITAR SYSTEMS 4-Way replacement electronics for LEFTY Fender Telecaster! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import telecaster electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each SGS FTLH4W system: 2) Split shaft Left Hand Taper CTS 250K Vintage Style Audio Pots, with Nut, Lock and Dress Washer. 2) brass adapter sleeves to convert split shaft to solid shaft 1) TRITAN 4 way pickup selector switch 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) Vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) Switchcraft #11 input jack with shrink wrap strain relief on both terminals 1) Wiring diagram (see photo section) 1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Wiring Harness for LEFTY Fender Esquire! CTS, Switchcraft, CRL, Orange Drop, NEW

SGS Fender ESQUIRE “Eldred Mod” Style Single Pickup “LEFTY” Electronics Upgrade!! The sad truth is…. that many left handed guitars, even expensive ones use right handed pots! Why? Because most companies are to cheap to install the proper left handed pots that only cost a few dollars more. They also don’t want to be bothered with the cost of reverse wiring for such a small percentage of the market. So what you might have is a great playing lefty with right handed electronics on board. The taper and control on the pots will be all wrong! Here is the solution…. STARR GUITAR SYSTEMS replacement electronics for LEFTY Fender Esquire! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. We use actual CTS left handed pots for the proper taper and control! Upgrade your import tele esquire Lefty electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! CRL 3 way Switch Positions: 1) Volume with no tone 2) Standard volume & .022 mfd orange drop tone 3) Volume & .005 mfd fixed tone Included in each SGS LEFTY Fender ESQUIRE single pickup Telecaster system: 2) USA made LEFT HANDED CTS 250K Vintage Style Audio Pots, split shaft with Nut, Lock and Dress Washer. (brass adapter sleeves included for conversion to solid shaft) 1) USA made CRL 3 way pickup selector switch 1) “Orange Drop” .022 mfd 100 volt Capacitor 1) .005 mfd Capacitor 5) USA made Gavitt vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) USA made Switchcraft #11 input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section) 1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Wiring Harness Upgrade For Telecaster Esquire NEW! CRL – CTS – Mallory – Gavitt!

“Eldred Mod” style FT Esquire PRO model! With the success of my FT Esquire STANDARD model, we have now added an upgrade version! Same pots, jack, and switch… but we have replaced the Orange Drop capacitor with a Mallory 150 Series .022 capacitor, added a treble bleed circuit, replaced the ceramic .005 capacitor with a Mallory 150 series .0047 capacitor for the fixed tone, and also replaced the standard black & white vintage cloth wire with BLACK & BLUE Gavitt cloth wire that we have custom made for us! STARR GUITAR SYSTEMS replacement electronics for Fender ESQUIRE single pickup Telecaster! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import ESQUIRE telecaster electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING! CRL 3 way Switch Positions: 1) Volume with no tone 2) Volume & .022 Mallory capacitor 630v tone control 3) Volume & .0047 Mallory capacitor 630v fixed tone Included in each SGS Fender ESQUIRE single pickup FTESQPRO system:2) USA made CTS 250K Vintage Style Audio Pots, solid shaft with Nut, Lock and Dress Washer.1) USA made CRL 3 way pickup selector switch with black tip 1) .022 Mallory 630 volt Capacitor 1) .0047 Mallory 630volt Capacitor (fixed tone) 1) Treble Bleed Circuit – .001 uF capacitor & 100K 1/4 watt resistor wired in parallel5) Gavitt vintage style push back black (ground) and blue (hot) cloth covered wires, 22 gauge, pre-tinned, with a waxed braided cotton outer insulation. 1) Switchcraft #11 input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section)1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Peavey Foundation Bass wiring harness upgrade! CTS – Orange Drop – Switchcraft!

Peavey Foundation Bass wiring harness upgrade NEW!! STARR GUITAR Systems replacement electronics for the classic Peavey Foundation Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, jack wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING! Included in each SGS PVFB set: 3) CTS 250K Audio Taper Pots, split shaft, with Nut, Lock and Dress Washer. 2) treble bleed circuits for each volume control 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) GAVITT vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) Switchcraft #151 input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section) 1) Assembly template board Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 www.facebook(dot)com/starrguitarsystems WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Wiring Harness for Gibson Flying V 1958 PRO

STARR GUITAR SYSTEMS Harness upgrade for Gibson Flying V 1958, PRO version, with MOD paper & oil capacitor. This fits USA made 1958 style Flying V’s. (if you are not sure if the layout of your controls are 1958 or 1967 style, check control reference image) 3) CTS 500K split shaft short pots 1) Switchcraft L style 3 way switch 1) Switchcraft #11 input jack 1) MOD paper & oil .022 Capacitor 50 volt Gavitt vintage style cloth wire BLACK & BLUE, pre-tinned 20 gauge solid tinned copper ground wires Assembly board Wiring diagram (see photo section) Premium replacement electronics for your Gibson Flying V! Each set is assembled, hand wired and soldered in the USA using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number

Wiring harness upgrade for Gibson Flying V model 67!

STARR GUITAR SYSTEMS Harness upgrade for USA made Gibson 67 Flying V! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. All units have their own serial number, and are signed by Dave Starr. FREE SHIPPING! 3) CTS 500K split shaft short pots 1) Switchcraft L style 3 way switch 1) Switchcraft #11 input jack 1) Orange Drop .022 Capacitor 100V 1) Gavitt vintage style cloth wire black & white 1) 22 gauge solid tinned copper ground wires 1) Assembly board 1) Wiring diagram (see photo section above) Want to check out my “PRO” V Harness? Visit this link: https://www.ebay.com/itm/Wiring-harness-PRO-upgrade-for-Gibson-Flying-V-58-and-67-NEW/283162462771 Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.