Gibson 335 Harness Upgrade: CTS, Switchcraft, Orange Drop, P/P Tone Pots! NEW!

Gibson 335 Harness Upgrade! CTS, Switchcraft, Orange Drop Caps, P/P Tone Pots, NEW!Comes with 2 Push/Pull tone pots for coil split operation! (pickups must have 4 conductor wiring)Free Shipping! STARR GUITAR SYSTEMS 50’s style wiring replacement electronics for USA made Gibson ES 335! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Replace your old worn out parts with these premium replacement units! All units are signed by Dave Starr and have their own serial number. Included in each 335PP set: 2) CTS 500K audio volume pots, split knurled shaft, Includes nut, lock, and dress washer. 2) 500K Push/Pull Tone pots, split knurled shaft, Includes nut, lock, and dress washer. 2) Orange Drop .022 capacitors 100 volt 1) Switchcraft short 3 way switch 1) Switchcraft #11L input jack 1) Wiring diagram (see photo section for basic 335 wiring. Let me know the model/brand pickups you have, and I will assist you with the P/P pots) 1) Assembly template board 7) Gavitt vintage style cloth guitar wires Note: Most guitars manufactured overseas in Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, TX, 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Electronics Upgrade for Gibson Les Paul! With Bourns Push/Pull Pots!

This system includes everything you need to wire a Gibson Les Paul Standard, Custom, Deluxe, etc. – but with push/pull tone pots that will provide you some additional tonal flexibility and options vs. standard tone pots. 4-conductor humbucker pickups are required. You can use the push/pull pots in any way you’d like: coil split, Series/Parallel, Phase Reverse , etc. I use push/pull pots in one of my Les Pauls for the coil split mod. STARR GUITAR SYSTEMS 50’s style wiring replacement electronics for USA made Les Paul’s! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Get rid of the tone sucking PCB electronics on your modern Les Paul, or replace your old worn out parts with these premium replacement units! All units are signed by Dave Starr. FREE SHIPPING in the USA! Included in each LPPPx2 LONG SHAFT set: 2) USA made CTS 500K audio taper long shaft VOLUME pots. 3/4 inch tall threaded bushing with 3/8 inch diameter. 24 spline split knurled shaft. Includes nut, lock, and dress washer. 2) Bourns 500K Push/Pull Audio Taper TONE Pots, 3/4″ Long Threaded Bushing, Split Shaft, DPDT 2) Sprague “Orange Drop” .022 mfd 100 volt Capacitors 1) Wiring diagram (see photo section for basic LP Wiring, email me the model/brand pickups you have, and I will assist you with the P/P pot wiring!) 1) Assembly template board Note: Most guitars manufactured overseas in Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly.Starr Guitar Systems PO Box 3132 Conroe, TX, 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Gibson Thunderbird Bass “PRO” Harness! CTS, Switchcraft, Gavitt, & Mallory Cap!

Gibson Thunderbird Bass “PRO” Wiring Harness! CTS, Switchcraft, Gavitt Wire, & Mallory Cap! STARR GUITAR replacement electronics for Gibson Thunderbird 3 control Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each SGS “PRO” Thunderbird Bass Harness: 2) CTS 500K Audio Pots (Volume Controls), split shaft, with Nut, Lock, and Dress Washer 1) CTS 250K Audio Pot (Master Tone), split shaft, with Nut, Lock, and Dress Washer 1) Mallory .047 Capacitor 4) Gavitt vintage style push back BLACK (ground) and BLUE (hot) cloth covered wires, 22 gauge (custom made for us by Gavitt Wire USA!) 1) 18 gauge solid tinned copper master ground wire 1) Switchcraft #11L input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section)1) Assembly template board IMPORTANT: if your bass needs the long switchcraft #151 cannon style jack, I have them here at this link:www.ebay.com/itm/Switchcraft-151-Mono-Long-Threaded-Jack-with-GAVITT-Wire-NEW/283455306152 Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. If so, you will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Please follow this link if you want to see my Thunderbird “Standard” wiring harness:www.ebay.com/itm/Gibson-Thunderbird-Bass-Harness-CTS-Switchcraft-Gavitt-Wire-Orange-Drop/282831573839 Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 www.facebook(dot)com/starrguitarsystems WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Fender P- Bass Harness Upgrade System! CTS, Switchcraft, & Orange Drop Cap!

STARR GUITAR SYSTEMS P-Bass “Standard” for Fender P-Bass Premium replacement electronics for your Fender P-Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. I also do installations! Included in each SGS P-Bass “Standard” set: 2) USA made CTS 250K Vintage style audio taper short shaft pots, with nut, lock and dress washer. (available in either split or solid shaft) 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) Vintage style push back BLACK (ground) and WHITE (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) USA made Switchcraft #11 input jack with heat shrink strain relief on both terminals. 1) Wiring diagram (in photos above) 1) Assembly template board Note: This P-Bass system is available in either split or solid shaft, the price is the same. Please let me know what type you want. Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Fender P-Bass Electronics Upgrade! Bourns, Mojo Tone, Gavitt & Orange Drop Cap!

STARR GUITAR SYSTEMS for Fender P-Bass. This system is a great deal if you want to improve your bass and still save some money! The BOURNS mini pots are a bit less money then their larger brothers, but still sound great! And, you also get a Mojo Tone input jack, Orange Drop capacitor, and Gavitt guitar wire! FREE SHIPPING IN THE USA! Great for many import basses that have smaller/narrower control cavities that wont fit full size pots! Premium replacement electronics for your Fender P-Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. Included in each PBMB set: 2) 250K BOURNS Mini Pots, Audio Taper, 24 spline split shaft, with hardware 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) Gavitt 22 gauge guitar wire 1) Mojo Tone input jack with heat shrink strain relief on both terminals. 1) Wiring diagram (in photos above) 1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Fender P-Bass Harness Upgrade! CTS, Switchcraft, & Russian PIO .047 Cap!

STARR GUITAR SYSTEMS for Fender P-Bass Premium replacement electronics for your Fender P-Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. I also do installations! Included in each SGSPBVR P-Bass system: 2) USA made CTS 250K Vintage Style Audio Pot, solid shaft with nut, lock and dress washer. 1) Russian K42Y-2 Paper-in-Oil Capacitor .047uF 250v 4) Vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) Switchcraft #11 input jack with heat shrink strain relief on both terminals. 1) Wiring diagram (in photos above) 1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Dual Mode wiring harness upgrade for Fender P-Bass! .047 & Bypass! NEW!

STARR GUITAR SYSTEMS P-Bass Dual Mode upgrade for Fender P-Bass! This system uses a Bourns 250K Push/Pull pot in the tone position. In the down position, you bypass the tone control completely and get the straight/pure sound from your pickup, volume, and amp. Pull the Push/Pull pot to the up position and this activates the standard tone control operation with an Orange Drop .047 100 volt Capacitor. Can also be used as an A/B type switch where you can go from clean to a pre-set on the capacitor mode. Premium replacement electronics for your Fender P-Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. Free Shipping in the USA! Included in each Starr Guitar Systems PBDM set: 1) CTS vintage style 250K solid shaft audio volume pot. Includes nut, lock, and dress washer1 Bourns 250K Push/Pull tone pot, split shaft. Includes nut, lock, and dress washer, includes brass adapter sleeve to convert to solid shaft 1) Orange Drop capacitor .047 100 volt 1) Switchcraft #11 input jack with heat shrink strain relief on both terminals 3) Gavitt 22 gauge pre-tinned guitar wire, White & Black 1) Wiring diagram (in photos above)1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You might need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Fender P-Bass Harness Upgrade! With Deluxe CTS 295 Pots & Mallory Cap!

STARR GUITAR SYSTEMS for Fender P-Bass! With Deluxe CTS 295 Series Pots and Mallory .047 Cap! Premium replacement electronics for your Fender P-Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. Included in each Fender P-Bass PB295 control system: 2) CTS 250K “295 series” split shaft audio taper pot. 4 contacts on carbon wafer, lasts for 250,000 cycles. Threaded bushing is 0.25 inch tall, spline portion is 0.28 inch tall, 0.6 inch total height. Includes nut and star washer. 1) Mallory capacitor .047 2) brass sleeves to convert pots to solid shaft 4) Vintage style push back black (ground) and blue (hot) cloth covered wires, 22 gauge, custom made for us by GAVITT wire right here in the USA! 1) Switchcraft #11 input jack with heat shrink strain relief on both terminals. 1) Wiring diagram (see photo section) 1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 www.facebook(dot)com/starrguitarsystems WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop. www.wildestarr.comwww.facebook.com/DaveStarr7777www.facebook.com/starrguitarsystemswww.ernieball.com/artists/dave-starrwww.emgpickups.com/artist/index/view/id/407

Fender Jazz Bass Wiring Upgrade with pickup balance/blend control & Mallory Cap!

This is the PRO version of my STANDARD Jazz Bass VBT system! It includes a Mallory .047 Capacitor! STARR GUITAR SYSTEMS replacement electronics for Fender Jazz Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each JBVBTP (Volume-Balance-Tone) system: 1) CTS 250K Vintage Style Audio Pot for master volume, solid shaft, with Nut, Lock and Dress Washer. 1) CTS 250K Blend/Balance Linear Taper Pot, with Center Detent, with hardware, split shaft with brass adapter sleeve. 1) CTS 250K Vintage Style Audio Pot for master tone, solid shaft, with Nut, Lock and Dress Washer. 1) Mallory .047 mfd Capacitor 5) Vintage style push back black n blue cloth covered wires, 22 gauge, made by Gavitt Wire USA2) Gavitt white pickup hot leads coming off balance/blend pot. Heat shrink included.1) Switchcraft #11 input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section)1) Assembly template board NOTE: for my J-Bass VBT “Standard” wiring harness with Orange Drop cap, and black and white cloth wire, visit this link: https://www.ebay.com/itm/282251224544 Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.

Fender Jazz Bass Harness Upgrade System with pickup balance/blend control! NEW!

Fender Jazz Bass Harness Upgrade System with pickup balance/blend control! CTS, Switchcraft, Orange Drop .047! NEW! STARR GUITAR SYSTEMS replacement electronics for Fender Jazz Bass! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each SGS Jazz Bass Balance/Blend set: 1) CTS 250K Vintage Style Audio Pot for master volume, solid shaft, with Nut, Lock and Dress Washer. 1) CTS 250K Blend/Balance Linear Taper Pot, with Center Detent, with hardware, split shaft with adapter sleeve 1) CTS 250K Vintage Style Audio Pot for master tone, solid shaft, with Nut, Lock and Dress Washer. 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) Vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) Switchcraft #11 input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section)1) Assembly template board Check out this link for my PRO version of this harness: https://www.ebay.com/itm/Fender-Jazz-Bass-Wiring-Harness-Upgrade-with-pickup-balance-blend-control-NEW/283308965024 Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.