(1) Mallory capacitor. 047 uf, 630 volt. Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Simply attach your pickup wires, and bridge ground wire and you are ready to rock!
My top of the line system for Les Paul’s!!! Gibson Les Paul Harness Upgrade! CTS, Switchcraft, Emerson PIO Caps! STARR GUITAR SYSTEMS “LES PAUL PRO PLUS” 50’s style wiring replacement electronics for USA made Les Paul’s! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Available in both long and short shaft. Get rid of the tone sucking PCB electronics on your modern Les Paul, or replace your old worn out parts with these premium replacement units! All units have their own serial number, and are signed by Dave Starr. FREE SHIPPING IN THE USA! Included in each LPPP system: 4) CTS 500K audio taper long shaft pots. 3/4 inch tall threaded bushing with 3/8 inch diameter. 24 spline split knurled shaft. Includes nut, lock, and dress washer. These work best with push on knobs. 2) EMERSON oil-paper capacitors; 022uf Bridge, & .015uf Neck 1) Switchcraft Short Straight toggle switch with black cap, includes heavy duty 4 Conductor 22 Gauge Shielded Cable 1) Switchcraft 1/4 inch mono #11 input jack 3) 18 gauge solid tinned copper ground wires 1) Wiring diagram (sent via ebay messaging) 1) Assembly template board Note: Most guitars manufactured overseas in Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.
Gibson Firebird Harness Upgrade! CTS, Switchcraft, Mallory Caps! STARR GUITAR SYSTEMS FIREBIRD 50’s style wiring replacement electronics for USA made Gibson FIREBIRDS! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. All units have their own serial number, and are signed by Dave Starr. FREE SHIPPING IN THE USA! Included in each FB system: 4) 500K Audio Pots, CTS, split knurled shaft with nut, lock and dress washer. Threaded bushing is 3/8″ tall. These work best with push on knobs. 2) Mallory capacitors .022 630 volt 1) Switchcraft Short Straight toggle switch with black cap, includes heavy duty 4 Conductor 22 Gauge Shielded Cable 16″ NOTE: Please let us know what type switch you need, short straight or L type. See pics above. 1) Switchcraft 1/4 inch mono #11L input jack, threaded portion is 3/8″ long 3) 18 gauge solid tinned copper ground wires 1) Wiring diagram (see photo section) 1) Assembly template board Note: Most guitars manufactured overseas in Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.
ToneHounds Guitar Mods Wired Assembly for Fender P-Bass Premium replacement electronics for your Fender P-Bass! Each assembly is assembled, hand wired and soldered in my Northern California, USA shop using premium parts for best performance and a lifetime of use. Upgrade your import bass electronics, or replace your old worn out parts with these premium replacement assemblies! Simply attach your pickup and bridge ground wires and you are ready to go. USA made CTS 250K Vintage Style Audio Pots, complete with nut, lock and dress washer. I use J taper vintage taper pots for best control over the tone of the guitar, and brass bushings and shaft for the best reliability and performanceUSA .047uF Orange Drop CapacitorGavitt Vintage style push back cloth wire.- 7 strand, 22 gauge wire with a waxed braided cotton outer insulation. White is used for hot connections, black for groundUSA Switchcraft #11 input jack with heat shrink strain relief on both terminalsWiring diagram included in photos aboveShipped on a custom template for proper spacing and to keep secure during shipping Note: This assembly comes with solid shaft pots per Fender practice. If you prefer split shaft pots please contact me and I will build with no upcharge on the price. Contact me if you have any questions! Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6 mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Free 1st Class shipping in the Continental United States I also offer other assemblies for Teles, Strats, Les Pauls, Blender Circuits, PIO capacitors, and different capacitor values, Eric Johnson and David Gilmour assemblies, treble kits…just check my other listings. If you have any questions with assembly or what components work best for you, give me a shout. I’ve been on Ebay for over 22 years, check out my feedback and buy with confidence. Thanks!Some feedback from buyers of my wired harnesses:Excellent product!! Amazing craftsmanship!! Buy one now!! So pleased!!Just as described!Super fast shipping and great workmanship. Thanks !Well put together Terrific service Highly recommendedVery nice productGood honest sellerFast delivery…product was in good condition. Took 10 minutes to unwrapVery good communication and nice product, thanks!Fast shipping, exactly as described!Excellent item and fantastic seller very responsive and helpful with questions
7 Way Sound Wiring Harness Upgrade For 3 Pickup Fender Nashville Telecaster! NEW! STARR GUITAR SYSTEMS (SGS) Fender Nashville “7 Way Sound”. The push/pull pot tone control works to enable an additional 2 sounds in addition to the standard 5 Nashville Tele sounds. In position 4 with the P/P up, you get all 3 pickups together. In position 5 with the P/P up, you get bridge & neck pickups together. All units have their own serial number, and are signed by Dave Starr. FREE SHIPPING! Included in each SGS Fender Nashville 3 Pickup Tele “7 Way Sound” Harness model FTN7W: 1) CTS 250K audio taper vintage style solid shaft volume control 1) Bourns 250K Push/Pull tone pot, split shaft, with brass adapter sleeve 1) Mallory .022 mfd 630 volt capacitor 1) CRL 5 way switch 1) Treble bleed mod: .001 uF capacitor & 100K 1/4 watt resistor 1) Switchcraft 1/4 inch mono #11 input jack with heat shrink strain relief on both terminals. 6) Gavitt vintage style push back BLACK (ground) & BLUE (hot) cloth covered wires 22 gauge pre tinned. 1) Wiring diagram (see photo section) 1) Assembly template board WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.
STARR GUITAR SYSTEMS replacement electronics for Fender Telecaster! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import telecaster electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each SGSFTP Fender Telecaster “PRO” set: 2) USA made CTS 250K Vintage Style Audio Pots, SOLID SHAFT, with Nut, Lock and Dress Washer. 1) USA made CRL 3 way pickup selector switch 1) Mallory .047uF @ 630V capacitor 1) Treble bleed mod. Gives you more uniform tone from 1 to 10, and a more rounded sound at low volume 4) Vintage style push back black (ground) and blue (hot) cloth covered wires, 22 gauge, pre-tinned, custom made for us by GAVITT wire here in the USA! 1) Switchcraft #11 input jack with heat shrink strain relief on both terminals 1) Wiring diagram (see photo section)1) Assembly template board Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.
This gives you the usual Tele sounds in the first three positions. But in position 4, you get both pickups in series like a humbucker. It’s a big boost in output and a big, fat tone. But you need to make one important adjustment: The neck pickup’s cover has to be grounded with a separate wire. That means you have to flip the pickup over and cut the little un-insulated jumper wire that connects to the cover. That leaves a 1/4-inch nub of wire connected to the cover. Attach a new wire to that, and connect it to ground. This wiring works great with any vintage-output Tele pickups. STARR GUITAR SYSTEMS 4-Way replacement electronics for Fender Telecaster! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Upgrade your import telecaster electronics, or replace your old worn out parts with these premium replacement units! Simply attach your pickup wires, and bridge ground wire and you are ready to rock! All sets are signed by Dave Starr and have their own serial number. FREE SHIPPING IN THE USA! Included in each SGS Fender Telecaster “FT4way” set: 2) Solid shaft CTS 250K Vintage Style Audio Pots, with Nut, Lock and Dress Washer. 1) Tritan 4 way pickup selector switch 1) “Orange Drop” .047 mfd 100 volt Capacitor 4) Vintage style push back black (ground) and white (hot) cloth covered wires, 22 gauge, with a waxed braided cotton outer insulation. 1) Switchcraft #11 input jack with shrink wrap strain relief on both terminals 1) Wiring diagram (see photo section) 1) Assembly template board Note: Check out my ebay store Telecaster section for more Tele models!! Note: Most guitars manufactured overseas in South Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these CTS pots properly. Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE:Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.
STARR GUITAR SYSTEMS replacement electronics for 72 Fender Tele Deluxe! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Replace your old worn out parts or upgrade your current wiring with these premium replacement units! All units are signed by Dave Starr and have their own serial number. Included in each 72FTD set: 1) Switchcraft 3 way L style (right angle) toggle switch with 15 inch 4 conductor wire 4) CTS 500K audio pots, solid shaft, includes nut, lock, and dress washer. 1/4 inch threaded portion. 2) MALLORY .022 capacitors 630v 3) 18 GAUGE solid tinned copper ground wires.
This system includes everything you need to transform a Gibson Les Paul into the famous “Jimmy Page” wiring. 4-conductor humbucker pickups are required. The Bourns Push/Pull pots allow you to split your humbuckers into single coil pickups, allows both pickups to be put out of phase, and can put both pickups in series as well. AND…with the 3 way switch in the bridge position, the neck tone pot will act as a kill switch when pulled up! STARR GUITAR SYSTEMS 50’s style wiring replacement electronics for USA made Les Paul’s! Each set is assembled, hand wired and soldered in the USA by Dave Starr using premium parts. Get rid of the tone sucking PCB electronics on your modern Les Paul, or replace your old worn out parts with these premium replacement units! All units are signed by Dave Starr. FREE SHIPPING in the USA! Included in each LPJP system: 4) Bourns 500K Push/Pull Audio Taper volume & tone pots, 3/4″ Long Threaded Bushing, Split Shaft, DPDT 2) “Orange Drop” .022 mfd 100 volt Capacitors 1) Wiring diagram (see photo section) 1) Assembly template board Note: this is a very complex wiring system and needs to be installed by a qualified guitar repair technician Note: Most guitars manufactured overseas in Korea, Japan, China, Indonesia and Mexico use 6mm metric pots and have metric sized holes drilled. You will need to enlarge the pot holes to 3/8″ to fit these pots properly. Starr Guitar Systems PO Box 3132 Conroe, TX, 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.
Gibson Explorer Model “EXP 83” Passive Pickups Wiring Harness Upgrade! CTS – Switchcraft – Orange Drop – Gavitt! NEW! FREE SHIPPING! STARR GUITAR SYSTEMS Harness upgrade for USA made Gibson Explorer “EXP 83”! Each set is assembled, hand wired and soldered in the USA using premium parts. All units have their own serial number, and are signed by Dave Starr. 3) CTS 500K split shaft pots (3/8 inch thread length) 1) Switchcraft L style 3 way switch with deep thread nut 1) Switchcraft #11 input jack 1) Orange Drop .022 Capacitor 100V Gavitt vintage style cloth wire black & white 18 gauge solid tinned copper ground wires Assembly board Wiring diagram (see photo section) Starr Guitar Systems PO Box 3132 Conroe, Texas 77305 WHO WE ARE: Starr Guitar Systems (SGS) owner Dave Starr has been playing guitar and bass professionally (WildeStarr, Vicious Rumors, and CHASTAIN) for over 30 years, and doing guitar repair for over 30 years as well. Dave has put his years of experience as a pro to come up with his own line of guitar & bass electronic upgrade systems. So, when you buy from Dave, you are not just buying gear from a guitar technician… you are buying gear from a PRO MUSICIAN who has been there and done that….. recorded over 15 albums, toured the world multiple times, MTV videos, artist endorsements (currently signed with ERNIE BALL strings and EMG pickups), etc. Every SGS unit comes with all of that experience behind it… what works and what doesn’t, because Dave has pretty much seen and done it all. And, every SGS unit is custom built and assembled by hand one at a time by Dave here in his Houston Texas shop.
